Lonestar Plumber in The Colony
Shower Repair Flower Mound, TX
Shower repair in Flower Mound ends with a full test: hot, cold and a flush elsewhere in the house to check the balance, with the tub and floor wiped down after. Before that, you hear where the water is really ending up and what the fix costs. Most fixes go in through the handle, not the tile.

Flower Mound homes and shower repair
Most showers in town went in from the 1990s on; the town's median house dates to 1997. Many valves from that period are single-handle designs, often pressure-balancing, and their cartridges are now some thirty years into a job that wears seals and sticks spools. A temperature jump during a toilet flush, or a head that keeps dripping after you shut it off, is that cartridge talking. Older two-handle valves turn up too, and their stems take new washers and seats. Hall baths of that era mostly pair a tub with the shower, and a worn diverter that lets water escape from the spout is a regular find.
The water plays a part. The Town buys it treated from two wholesalers, the Upper Trinity Regional Water District, known as UTRWD, and Dallas, all of it lake water, and publishes no hardness figure. Mineral film still builds inside showerhead nozzles and on cartridge spools over the years, which is why a spray thins slowly and a handle grows stiff. A new cartridge and a cleaned or replaced head fix both, with no wall opened. Cleaning a stiff cartridge rarely restores its seals, so it is replaced rather than soaked.
When the valve body itself has to go, the job changes. New valves go in to the 2024 IRC, the code the Town adopted on October 1, 2025. A shower almost never has its own shutoff, so the whole house goes off at its main valve, normally at the front by an outdoor faucet, or at the meter box with a curb stop key. In two-story homes, a leak from an upstairs valve or drain shows on the ceiling below first, and that drywall is usually the easier side to open.
Flower Mound at a glance
- County
- Denton County (a small part in Tarrant County)
- Typical home
- Median year built 1997
- Water supply
- Town of Flower Mound, buying treated water from UTRWD and Dallas
- Permit office
- Building Inspections, Town Hall, 2121 Cross Timbers Rd., 75028
- Permit portal
- eTRAKiT online permitting and inspections
- From our office
- About 13 miles from our Main St office in The Colony, mostly by SH 121
Signs your shower needs a repair
- A showerhead or tub spout still dripping once the handle is off
- Scalding or cold bursts when someone flushes
- Never hot enough, even turned all the way
- Weak spray, or a tub spout that runs in shower mode
- A stained ceiling below or a wet baseboard beside it
Questions from Flower Mound
Is a new shower valve a permit job in town?
The Town's guidelines bring plumbing under its permit rules, naming heater jobs first and water and sewer line repairs next, and a new valve body is plumbing behind the wall. Building Inspections can confirm the details for your address, and eTRAKiT is where the inspection gets booked. A cartridge swap through the trim is a repair to the existing valve.
We are buying a 1990s house in town. What should we check in the showers?
Run each shower hot and cold, flush a nearby toilet while it runs, and watch the temperature. Look under the trim plate for staining and at the ceiling below any upstairs bath. Valves from that decade often still have their original cartridges, and replacing one now is simpler than chasing a drip after the closing.
Why won't my shower get hot enough?
If the rest of the house has hot water, check the valve. Most single-handle valves have a limit stop that caps how far the handle turns toward hot. It may be set low or knocked loose. A worn cartridge is the other usual cause.
Booking in Flower Mound
Call (469) 940-4415 and describe what the shower does and where water shows up. If the trim plate carries a maker's name, note it. Showers rarely have a shutoff of their own, so if water keeps running hard, close the main valve.
